Our Superfilter is positioned savely in a proper housing with M9.5 x 1 threads for use with all leading sport weapons.
Simply screwed in between rearsight and rearsight-iris.
Conventional sights suffer from the disadvantage that
the human eye is not capable of focalizing both front sight (picture 1) and target picture (picture 2) at the same time.
The Gehmann MicroSight (picture 3) however facilitates contemporaneous focus of front sight and target by using only one particular filter.
Our Gehmann Superfilter has no magnification or optical characteristics, so it is in accordiance to the latest I.S.S.F. rules.
The shooter’s vision should be corrected for Distance Viewing. Both front sight and target will be blurred if the shooter is near-sighted
or is using target shooting glasses designed to provide a clear image of the front sight.
The Gehmann Superfilter AOS MicroSight TM
will work with all rearsight irises incorporating M9.5 x 1mm threads including those that contain focusing and/or magnification
but it is unlikely to work well if combined with front sight magnification.
Pay attention:
The Gehmann Superfilter AOS MicroSight TM
must be reasonably aligned with the front sight. If large movement of the rear sight is required for wind or long range,
the rear sight should be aligned with the front sight when in the middle of the range of rear sight adjustment.
|
 |
Special coloured filters for use with the Centra Spy rearsight
You can buy the single colours here, or the full set below
These attach easily to the rear tube on the Spy rearsight
|
|
Special coloured filters for use with the Centra Spy rearsight
You can buy the full set here, or single colours above
These attach easily to the rear tube on the Spy rearsight
|
|
Built for the 7002 rearsight
Long sight tunnel to act as an anti-glare tube
As it bridges the receiver it acts as a vibration dampener
Increases the room you have to mount your sight by about 20mm.
|
|
New ISSF ruling compliant
30mm single layer
Held in position by popping onto your iris
Can be used on left side or right side
Suitable for all disciplines
|
|
New ISSF ruling compliant
30mm single layer
Held in position by popping behind your iris
Can be used on left side or right side
Suitable for all disciplines
|
|
New ISSF compliant blinder
Fits all current Anschutz & Centra irises
Fits and removes in 2 seconds
|
|
Anschutz rubber eye cup
Replace the one you lost!
Will fit all current Gehmann / Anschutz / Centra irises
Fits standard Anschutz aperture also
|
|
Standard rear aperture for Anschutz rearsights
1.1mm size
Replace the one you lost on your sights
|
|
Patented design giving identical degrees of cant to front and rear sights
Comprising a base for the rearsight and a completely new foresight
Rearsight base swings radially round the receiver rail and bore-line
The foresight swings radially round the bore-line
Far exceeds existing systems where only the rearsight has cant adjustment
No need for any further form of adjustment once cant has been set
Made for air rifles but the rear base can be used on smallbore rifles, foresight not used
Available for Anschutz, Feinwerkbau & Walther
|
|
Takes 25mm spectacle lens
Most exciting product for spectacle wearers in years!
Lens is held perfectly central in front of your iris
No more trying to line up your spectacles and head
The lens holder is not ISSF compliant but for the club shooter entering local competitions it is superb.
The lens can be held far enough away from the rear sight to accomodate the range of Anschutz and Gehmann irises
|
|
Head alignment tool by Centra
Will fit to all modern Anschutz & Centra irises
Gets your eye exactly behind the rearsight
Gets your at the correct distance from the rearsight
Cheap way to save a lot of hassle adjusting your head and cheekpiece
|
|
Head alignment tool by Centra
Will fit to all non-Centra irises, Gehmann etc
Gets your eye exactly behind the rearsight
Gets your at the correct distance from the rearsight
Cheap way to save a lot of hassle adjusting your head and cheekpiece
|
|
Fit 7002 and 6805 Anschutz rearsights
Available in three colours
Great for colour coding different sights for different ranges
They look rather nice too!
Matching bolt handles available
|
|
Brings the rear sight futher to the rear.
Useful for benchrest
Complete with front block
Adds 9mm elevation
Optional distance kit (see sight block section) to allow variable elevation
|
|
